<본삭금>dns client event 1014-미치겠어요ㅠㅠ 헬프미..

공유기 사용자입니다. 공유기 문제인가 해서 벨킨공유기->티피링크로 교환도 해봤지만 똑같은 증상이 여전히 발생합니다.

위의 dns 오류가 모두 인터넷 끊김은 아니었으나 항상 인터넷이 팅겼다가 자동으로 연결되었을때는 사진속의 이벤트가 발생합니다.

주기는 대략 5일~10일사이 정도에 발생합니다.(특이하게 항상 오전 3시 전 후로 인터넷이 몇 초동안 끊겼다가 다시 연결됩니다. 하지만

그사이에 게임은 튕기고 아침에 일어나보면 접속종료가 되어있어요.

열심히 구글링을 해서 마소의 안내페이지를 발견하긴 했는데요. 두번째 방법은 해봤는데 별 소용이 없었고 나머지는 어쩌란 말인지 잘 모르겠어요.

아래는 마소의 안내멘트입니다.

Method one: Disable RSS, Autotuning, and Taskoffload

1. Run the following command in an elevated command prompt in Windows 7:

netsh interface tcp set global rss=disabled

netsh interface tcp set global autotuninglevel=disabled

netsh int ip set global taskoffload=disabled

2. Disable the Scalable Networking Pack (SNP) in Windows 7 by changing the registry settings as follows:

Perform a full-system backup before you disable the SNP.

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters]

EnableTCPChimney=dword:00000000
EnableTCPA=dword:00000000
EnableRSS=dword:00000000

If the registry keys do not exist, create them, and then assign the previous values.

Method two : Disable TCP/IP v6

To disable TCP/IP v6

1. Click Start, click Control Panel, click Network and Internet, and then click
View network status and tasks.

2. In the left pane, click Manage Network Connections.

3. Right-click Local Area Connection, and then click Properties.

4. In the pop-up box, clear the Internet Protocol Version 6 (TCP/IPv6) check box.

5. Click OK, and then restart your computer.

To enable TCP/IP v6

1. Follow steps 1 through 3 in the previous procedure.

2. In the pop-up box, select the Internet Protocol Version 6 (TCP/IPv6) check box.

3. Click OK, and then restart your computer.

Method three: Enable the spanning tree portfast setting in your router

This action varies depending on your infrastructure router. Consult your manufacturer for further details.

Method four: Set you router and PC to communicate on same channel and standard manualy

1. Go to your router admin page which should be 192.168.1.1 (confirm with router manufacturer).

2. Navigate to WiFi settings and choose a channel which should comply with your location, for ex: 11. Save.

3. Choose Standard to broadcast WiFi signal as G only not abgn, bgn, gn (If your router is N capable and any PC in your home/office is only G ready). Save.

4. Go to your PC Network and Sharing Center (Windows 7) and Click on Change Adapter Settings, select you WiFi adapter, right click and choose Properties.

5. In pop up window select Configure, in next window click on Advance tab and browse settings there and choose same channel you choose in you router for ex: 11 and the same standard as G not abgn, bgn or gn. Save and Exit.

혹시 dns client event 1014 오류관련해서 해결방법을 아시거나 경험담이 있으시다면 도와주세요.

참고로 각종 드라이버 최신으로 업데이트 다 해보고,인터넷에 나와있는 dns오류관련 다 해봤어요;;